{"title":"ADBL New Products","description":null,"products":[{"product_id":"adbl-ppf-gel","title":"ADBL PPF Gel | Multipurpose Installation Gel","description":"\u003cp dir=\"ltr\"\u003eADBL PPF Gel is a water-based installation gel for paint protection film (PPF). It gives you a long working time and precise control when you position film on difficult panels. It is roughly 99% water with added slip agents. That means you can slide and reposition film without the adhesive grabbing too early.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003eStandard slip solution, made from water and a few drops of baby shampoo, runs off vertical panels and dries quickly. On complex shapes, that leaves you rushing. PPF Gel stays where you put it, so you have time to stretch film around mirrors, sharp body lines and raised or extruded trim without the adhesive lifting or pulling.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhere it works best\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eWrapping mirror caps and other compound curves\u003c\/li\u003e\n\u003cli\u003eStretching film over raised edges, badge recesses and extruded trim\u003c\/li\u003e\n\u003cli\u003eInstalls where exact positioning matters, such as headlights and bumper edges\u003c\/li\u003e\n\u003cli\u003eGloss black trim and screens, where you need a fast, clean install\u003c\/li\u003e\n\u003cli\u003eNear rubber seals, where it helps stop dirt washing out from under the seal and onto the film\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 dir=\"ltr\"\u003e\u003cbr\u003e\u003c\/h3\u003e\n\u003ch3 dir=\"ltr\"\u003eProduct Information\u003c\/h3\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct type:\u003c\/strong\u003e PPF installation gel (slip gel)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBase:\u003c\/strong\u003e Water-based, approximately 99% water with slip agents\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDilution:\u003c\/strong\u003e Use neat or dilute up to 1:3 with water\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuitable for:\u003c\/strong\u003e Paint protection film installs, including on gloss black trim and screens\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Rinses off easily with water\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 500mL, 1L\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 dir=\"ltr\"\u003e\u003cbr\u003e\u003c\/h3\u003e\n\u003ch3 dir=\"ltr\"\u003eDirections for Use\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003ePreparation\u003c\/strong\u003e\u003c\/p\u003e\n\u003col dir=\"ltr\"\u003e\n\u003cli\u003eClean and decontaminate the panel thoroughly before installing film.\u003c\/li\u003e\n\u003cli\u003eDecide on your dilution. Use it neat for the most working time on complex shapes. Dilute up to 1:3 (1 part gel to 3 parts water) for larger, simpler panels.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eApplication\u003c\/strong\u003e\u003cbr\u003e3. Apply an even layer of gel to the panel and to the adhesive side of the film.\u003cbr\u003e4. Position the film, then slide and stretch it into place. Reapply gel if the surface starts to dry before you finish.\u003cbr\u003e5. Once the film is positioned, anchor it and squeegee out the gel as normal.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eAfter installing\u003c\/strong\u003e\u003cbr\u003e6. Rinse away any excess gel from the surrounding area with clean water.\u003cbr\u003e7. Dry the surface around the working area thoroughly.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBest practice tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eUse it neat on mirrors and tight curves. The extra working time is where this product earns its place.\u003c\/li\u003e\n\u003cli\u003eMix only what you need for the day. A clean bottle and fresh mix reduce the risk of contamination getting under the film.\u003c\/li\u003e\n\u003cli\u003eWorking near rubber seals? Apply gel along the seal edge first. This stops dirt seeping out from under it and getting trapped beneath the film.\u003c\/li\u003e\n\u003cli\u003eDo not skip drying the surrounding area. Leftover gel on the edges can attract dust before the film settles.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSafety\u003c\/strong\u003e\u003cbr\u003eKeep out of reach of children. Avoid contact with eyes.\u003c\/p\u003e","brand":"ADBL","offers":[{"title":"500mL","offer_id":67702346383572,"sku":"ADB000679","price":19.95,"currency_code":"AUD","in_stock":false},{"title":"1L","offer_id":67702346416340,"sku":"ADB000680","price":24.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0621\/9300\/8852\/files\/adbl-ppf-gel-0-5l.jpg?v=1791850302"},{"product_id":"adbl-pro-slip","title":"ADBL PRO Slip | Professional PPF Installation Slip Solution","description":"\u003cp dir=\"ltr\"\u003eADBL PRO Slip is a concentrated slip solution for installing paint protection film (PPF), colour change wrap film and window tint. Mixed with demineralised water, it lets film slide into position without damaging the adhesive or leaving streaks. You can dilute it anywhere from 1:500 to 1:50, so one bottle covers everything from flat panels to tight, high-tension areas.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003eMany installers still make their own slip solution from water and baby shampoo. It works, but the strength is hard to keep consistent, and some shampoos leave residue that affects adhesion. PRO Slip is made for film work. It mixes to a measured strength every time, rinses off with cold water and leaves no deposits on the adhesive.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eKeeps the film slippery on unfinished areas so you can keep adjusting while you work\u003c\/li\u003e\n\u003cli\u003eReduces adhesive pulling and lines when you lift and reposition film\u003c\/li\u003e\n\u003cli\u003eRinses off cleanly with cold water\u003c\/li\u003e\n\u003cli\u003eHelps water clear from under the film faster, which speeds up the whole install\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSuitable for\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003ePaint protection film (PPF)\u003c\/li\u003e\n\u003cli\u003eColour change wrap film\u003c\/li\u003e\n\u003cli\u003eWindow tint\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003ePRO Slip vs ADBL PPF Gel\u003c\/strong\u003e\u003cbr\u003ePRO Slip is the everyday slip solution for spraying across the panel and the film. PPF Gel is a thicker gel for the hard parts of a job: mirrors, extruded trim and complex shapes where you need the film to stay put while you stretch it. Many installers run PRO Slip for the bulk of a car and switch to the gel for the difficult areas.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003e\n\u003cmeta charset=\"utf-8\"\u003eProduct Information\u003c\/h3\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct type:\u003c\/strong\u003e Concentrated PPF and film installation slip solution\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDilution:\u003c\/strong\u003e 1:500 to 1:50 with demineralised water\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuitable for:\u003c\/strong\u003e PPF, colour change wrap film, window tint\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemoval:\u003c\/strong\u003e Rinses off with cold water\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSizes:\u003c\/strong\u003e 500 mL, 1 L\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003eDirections for Use\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDilution guide\u003c\/strong\u003e\u003cbr\u003eStandard installs: 5 ml per 1 L of demineralised water\u003cbr\u003eHigh-tension areas or when you need longer working time: 10 to 15 ml per 1 L of demineralised water\u003cbr\u003eAbove 20°C: increase the amount of PRO Slip, as the solution dries faster in heat\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003ePreparation\u003c\/strong\u003e\u003c\/p\u003e\n\u003col dir=\"ltr\"\u003e\n\u003cli\u003eMix PRO Slip with demineralised water in a clean spray bottle at the strength you need.\u003c\/li\u003e\n\u003cli\u003eSpray the solution onto both sides of the film, the topcoat and the liner. This removes dust and neutralises static. Squeegee it off with a silicone squeegee.\u003c\/li\u003e\n\u003cli\u003eSpray the panel you are covering and squeegee it off to remove dust and loose dirt. Repeat if needed.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eApplication\u003c\/strong\u003e\u003cbr\u003e4. As you peel the liner off, spray the solution directly onto the adhesive side of the film.\u003cbr\u003e5. Spray the panel again just before laying the film.\u003cbr\u003e6. Place the film, position it, then squeegee out the solution from between the film and the paint.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eFinishing the edges\u003c\/strong\u003e\u003cbr\u003e7. To close up the edges, flush out any remaining slip solution with demineralised water. You can add 20% isopropyl alcohol (IPA) to help the edges grab.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBest practice tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eUse demineralised water, not tap water. Minerals in tap water can leave spots and contamination trapped under the film.\u003c\/li\u003e\n\u003cli\u003eStart at 5 ml per litre and adjust from there. Too much slip makes the film hard to anchor and slows down tacking.\u003c\/li\u003e\n\u003cli\u003eMix fresh on hot days and use the stronger ratio. Heat flashes off water quickly, and the film can grab before you are ready.\u003c\/li\u003e\n\u003cli\u003eKeep a separate bottle of PPF Gel for mirrors and complex trim, where a spray solution runs off too quickly.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSafety\u003c\/strong\u003e\u003cbr\u003eKeep out of reach of children. Avoid contact with eyes.\u003c\/p\u003e","brand":"ADBL","offers":[{"title":"500mL","offer_id":67702426566868,"sku":"ADB000687","price":18.95,"currency_code":"AUD","in_stock":true},{"title":"1L","offer_id":67702426599636,"sku":"ADB000688","price":23.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0621\/9300\/8852\/files\/adbl-pro-slip-0-5l.jpg?v=1791852918"},{"product_id":"adbl-surface-cleaner","title":"ADBL Surface Cleaner | PPF Pre-Install Cleaner and Degreaser","description":"\u003cp dir=\"ltr\"\u003eADBL Surface Cleaner is a pre-install cleaner and degreaser for preparing paint before you apply paint protection film (PPF), colour change wrap film or window tint. It removes grease, tar and old adhesive residue and leaves a clean, streak-free surface for the film to bond to. Most film failures, such as lifting edges, bubbles and contamination trapped under the film, start with poor prep. This is the step that prevents them.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003eIt also works as a cleaner for matte paint and matte film, removing dirt without polishing or changing the finish.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat it removes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eGreasy deposits and oily residue\u003c\/li\u003e\n\u003cli\u003eTar\u003c\/li\u003e\n\u003cli\u003eOld adhesive residue, including from previous film or badges\u003c\/li\u003e\n\u003cli\u003eDirt from matte paint and matte film\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSuitable for\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eSurface prep before PPF installation\u003c\/li\u003e\n\u003cli\u003eSurface prep before colour change wrap\u003c\/li\u003e\n\u003cli\u003eSurface prep before window tint\u003c\/li\u003e\n\u003cli\u003eRegular cleaning of matte paint and matte film\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSurface Cleaner vs an IPA wipe\u003c\/strong\u003e\u003cbr\u003eMany installers use isopropyl alcohol (IPA) as their final wipe. IPA is good at stripping light oils, but it struggles with tar and adhesive residue. Surface Cleaner is made to handle those heavier contaminants while still leaving a streak-free, residue-free surface for film. It is also safe on matte finishes, which strong solvent wipes are not always.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhere it fits in the ADBL film range\u003c\/strong\u003e\u003cbr\u003eSurface Cleaner preps the panel. ADBL PRO Slip is the slip solution for laying the film. ADBL PPF Gel is for complex shapes where you need more working time. Used together, they cover the full install from prep to finish.\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003eProduct Information\u003c\/h3\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct type:\u003c\/strong\u003e Pre-install surface cleaner and degreaser\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuitable for:\u003c\/strong\u003e Prep before PPF, colour change wrap and window tint; cleaning matte paint and matte film\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemoves:\u003c\/strong\u003e Grease, tar, old adhesive residue\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Streak-free, no deposits\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSizes:\u003c\/strong\u003e 500 mL, 1 L\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 dir=\"ltr\"\u003eDirections for Use\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003ePreparation\u003c\/strong\u003e\u003c\/p\u003e\n\u003col dir=\"ltr\"\u003e\n\u003cli\u003eWash the vehicle, then chemically and mechanically decontaminate the panels being covered. Use an iron remover and tar remover, followed by clay.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eCleaning\u003c\/strong\u003e\u003cbr\u003e2. Apply Surface Cleaner to a clean microfibre cloth. Do not spray it directly onto the panel.\u003cbr\u003e3. Wipe over the whole area where the film will go.\u003cbr\u003e4. Pay extra attention to the edges, gaps and seams of each panel. This is where the film edges sit, and where contamination causes lifting.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBefore installing\u003c\/strong\u003e\u003cbr\u003e5. Spray the panel with your slip solution, such as ADBL PRO Slip, to lift any remaining dust. Remove it with a silicone squeegee. You can skip this step when applying liquid film.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBest practice tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eTest on an inconspicuous area first, particularly on resprayed panels, fresh paint or matte finishes.\u003c\/li\u003e\n\u003cli\u003eUse a separate, clean microfibre for prep. A cloth that has touched wax, sealant or detail spray will put contamination straight back onto the panel.\u003c\/li\u003e\n\u003cli\u003eFlip and refold the cloth often. Once it picks up grease or adhesive, it starts spreading it around instead of removing it.\u003c\/li\u003e\n\u003cli\u003eDo edges last with a fresh face of the cloth. They hold the most contamination and matter most for adhesion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSafety\u003c\/strong\u003e\u003cbr\u003eUse in a well-ventilated area. Keep out of reach of children.\u003c\/p\u003e","brand":"ADBL","offers":[{"title":"500mL","offer_id":67702551773396,"sku":"ADB000683","price":25.95,"currency_code":"AUD","in_stock":true},{"title":"1L","offer_id":67702551806164,"sku":"ADB000684","price":31.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0621\/9300\/8852\/files\/adbl-surface-cleaner-0-5l.jpg?v=1791856761"},{"product_id":"adbl-mr-sponge","title":"ADBL Mr Sponge | Premium Wash Sponge","description":"\u003cp dir=\"ltr\"\u003eADBL Mr Sponge is a premium car wash sponge made from soft, durable foam, with two different sides. One side has a waffle texture and the other is smooth, so you can choose the feel that suits the panel and how you like to wash. It holds a large amount of water and wash solution, which keeps the paint lubricated as you work. That lubrication is what makes washing safe.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003eIt works with a traditional bucket wash and with rinseless and waterless-style washes, where a well-soaked sponge does most of the work.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhy two sides\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eWaffle side:\u003c\/strong\u003e The textured surface gives a little more bite on road film and grime, and carries plenty of suds.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSmooth side:\u003c\/strong\u003e A flat, soft face for gentle passes on delicate or freshly corrected paint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSuitable for\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eContact washing with regular car shampoo\u003c\/li\u003e\n\u003cli\u003eRinseless washes\u003c\/li\u003e\n\u003cli\u003ePaint, glass and painted trim\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWash sponge vs microfibre wash mitt\u003c\/strong\u003e\u003cbr\u003eA microfibre mitt pulls dirt deep into its pile and away from the paint, which makes it a strong choice for very dirty cars. A sponge glides more evenly, holds more solution against the surface, and releases dirt quickly when rinsed. That makes it a favourite for rinseless washing and for maintenance washes on cars that are cleaned regularly. Plenty of detailers keep both and choose based on how dirty the car is.\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003eProduct Information\u003c\/h3\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct type:\u003c\/strong\u003e Car wash sponge\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Soft, high-durability foam\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesign:\u003c\/strong\u003e Dual-sided, one waffle-textured face and one smooth face\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible with:\u003c\/strong\u003e Regular car shampoos and rinseless wash products\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003eDirections for Use\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003ePre-wash\u003c\/strong\u003e\u003c\/p\u003e\n\u003col dir=\"ltr\"\u003e\n\u003cli\u003eRinse the vehicle or pre-wash it with snow foam to remove loose dirt before any contact. A sponge should never be the first thing to touch a heavily soiled car.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWash\u003c\/strong\u003e\u003cbr\u003e2. Fully soak the sponge in your wash solution and squeeze it a few times so it loads right through the foam.\u003cbr\u003e3. Wash one panel at a time with light pressure and straight-line passes. Let the solution do the work.\u003cbr\u003e4. Rinse the sponge in a separate rinse bucket after each panel, ideally one with a grit guard, then reload it with solution.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eRinseless washing\u003c\/strong\u003e\u003cbr\u003e5. Soak the sponge in your rinseless solution and squeeze it over the panel to pre-soak it before wiping.\u003cbr\u003e6. Wipe the panel gently, then dry it straight away with a clean microfibre drying towel.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eAftercare\u003c\/strong\u003e\u003cbr\u003e7. Rinse the sponge thoroughly in clean water after use and squeeze out the excess.\u003cbr\u003e8. Let it air dry away from direct sunlight before storing.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBest practice tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eWork from the top of the car down and leave the lower sills and bumpers until last. These areas carry the heaviest grit.\u003c\/li\u003e\n\u003cli\u003eUse a separate sponge or mitt for wheels. Never use your paint sponge on them.\u003c\/li\u003e\n\u003cli\u003eIf you drop the sponge, rinse it thoroughly before it goes back on the paint. Grit picked up from the ground is the fastest way to scratch.\u003c\/li\u003e\n\u003cli\u003eUse the smooth side on soft or freshly polished paint, and save the waffle side for grimier panels.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"ADBL","offers":[{"title":"Default Title","offer_id":67711693914324,"sku":"ADB000736","price":14.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0621\/9300\/8852\/files\/adbl-mr-sponge-szt_1.jpg?v=1791890862"},{"product_id":"adbl-defoamer","title":"ADBL Defoamer","description":"\u003cp dir=\"ltr\"\u003eADBL Defoamer is an anti-foam additive for the waste water tank of upholstery and carpet extractors. Shampoos and pre-sprays foam up as you extract, and that foam builds up fast in the recovery tank. It cuts your working time short, can trip the float shut-off, and risks pulling moisture towards the motor. A small dose of Defoamer knocks the foam down so you can keep extracting without stopping to empty a tank that is mostly bubbles.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSigns you need a defoamer\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eThe recovery tank fills with foam long before it fills with water\u003c\/li\u003e\n\u003cli\u003eThe extractor loses suction or shuts off mid-job\u003c\/li\u003e\n\u003cli\u003eFoam is escaping from the tank or exhaust\u003c\/li\u003e\n\u003cli\u003eYou are emptying the tank far more often than the amount of dirty water justifies\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSuitable for\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eCarpet and upholstery extractors (wet extraction or “washing” vacuums)\u003c\/li\u003e\n\u003cli\u003eHot water extractors\u003c\/li\u003e\n\u003cli\u003eWet and dry vacuums used for extraction\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003cbr\u003eDefoamer goes in the dirty water tank only. It doesn’t touch the fabric and doesn’t change how your cleaning chemicals work. It pairs naturally with ADBL Pre-Spray, which is the sort of high-foaming upholstery pre-treatment that causes the problem in the first place.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e \u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003eProduct Information\u003c\/h3\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct type:\u003c\/strong\u003e Anti-foam additive for extractor waste water tanks\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDose:\u003c\/strong\u003e 20 to 50 ml per waste water tank\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuitable for:\u003c\/strong\u003e Carpet, upholstery and hot water extractors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSizes:\u003c\/strong\u003e 500 ml\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 dir=\"ltr\"\u003e\u003c\/h3\u003e\n\u003ch3 dir=\"ltr\"\u003eDirections for Use\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBefore extracting\u003c\/strong\u003e\u003c\/p\u003e\n\u003col dir=\"ltr\"\u003e\n\u003cli\u003ePour 20 to 50 ml of Defoamer into the empty waste water (recovery) tank of the extractor.\u003c\/li\u003e\n\u003cli\u003eUse the higher dose with high-foaming shampoos and pre-sprays, or on fabrics that have built up a lot of old cleaning product.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eUsing with ADBL Pre-Spray\u003c\/strong\u003e\u003cbr\u003e3. When extracting Pre-Spray, dose Defoamer at the same amount of Pre-Spray you used in your solution.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDuring the job\u003c\/strong\u003e\u003cbr\u003e4. Each time you empty the recovery tank, add a fresh dose before starting again.\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBest practice tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul dir=\"ltr\"\u003e\n\u003cli\u003eNever add Defoamer to the clean water or solution tank. It belongs in the waste side only.\u003c\/li\u003e\n\u003cli\u003eOld upholstery is often loaded with residue from previous cleanings and foams heavily. Start at the top of the dose range for interiors you haven’t worked on before.\u003c\/li\u003e\n\u003cli\u003eRinse the recovery tank thoroughly after each job. Leftover foam and dirty water make the next job foam faster.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSafety\u003c\/strong\u003e\u003cbr\u003eKeep out of reach of children. Avoid contact with eyes.\u003c\/p\u003e","brand":"ADBL","offers":[{"title":"500mL","offer_id":67712962265300,"sku":"ADB000475","price":22.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0621\/9300\/8852\/files\/05l-_DEFOAMER.webp?v=1791893041"}],"url":"https:\/\/microfibrecloths.com.au\/collections\/adbl-new-products.oembed","provider":"Microfibre Cloths","version":"1.0","type":"link"}